Cp-electronics VITM6-EBDSPIR-DD User Manual
Browse online or download User Manual for Relay Cp-electronics VITM6-EBDSPIR-DD. CP Electronics VITM6-EBDSPIR-DD User Manual
- Page / 12
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Overview
The EBDSPIR-DD PIR (passive infrared) presence
detector provides automatic control of lighting loads with
optional manual control.
Output Channel 1 comprises a mains voltage relay capable
of simple on/off switching, while Output Channel 2 provides
dimmable control of either DALI or DSI type ballasts.
Functioning as a presence detector, the unit can turn lights
on when a room is occupied and off when the room is
empty. Optional settings allow lights to be turned off in
response to ambient daylight, or to implement a maintained
illuminance (daylight harvesting) system.
The flexibility of having two channels and two switch inputs
allows the following example scenarios:
Dim an outside row of luminaires whilst internal fittings
are switched
Provide absence detection for two separate channels
Maintained illuminance system with manual up/down
controls
All functionality is fully programmable using an IR handset.
Features
Back features
Ceiling PIR presence detector – DALI / DSI dimming
EBDSPIR-DD, EBDSPIR-DD-IP
Product Guide
Retaining Spring
Retaining Spring
Power Input
& Switched
Output Connector
(Channel 1)
Dimmable
Control Output
Connector
(Channel 2)
Switch Input
Connector
PIR Sensor
Detects movement within the unit’s detection range,
allowing load control in response to changes in occupancy.
IR Receiver
Receives control and programming commands from an
IR (infrared) handset.
Light Level Sensor
Measures the overall light level in the detection area
Status LEDs
The LED flashes Red to indicate the following:
Power Input & Switched Output Connector (Channel 1)
Used to connect mains power to the unit and to connect a
switched load.
Dimmable Control Output Connector (Channel 2)
Used to connect DSI/DALI controllable ballasts and
transformers for dimmable loads.
Switch Input Connector
Two input terminals can be used to manually override the
dimming levels and override the lights on or off.
Walk Test LED active
when movement is detected
Valid setting received
Front features
Sensor Lens
which covers...
PIR Sensor
IR Receiver
Light Level Sensor
Status LEDs
Mounting Bezel
EBDSPIR-DD-IP-LT30
A special order version that can be used down to -30ºC
Summary of Contents
Page 1 - EBDSPIR-DD, EBDSPIR-DD-IP
Overview The EBDSPIR-DD PIR (passive infrared) presence detector provides automatic control of lighting loads with optional manual control. Outpu
Page 2 - Detection diagram
10 Parameter Name Default Value Range / Options Description UHS5 UNLCDHS Channel 1 –Switching Channel Detection Mode Presence Presence or
Page 3 - Burn-in
11 This page intentionally left blank
Page 4
12 Due to our policy of continual product improvement CP Electronics reserves the right to alter the specification of this product without prior not
Page 5 - Wiring diagrams
2 Detection diagram Area of lower sensitivity Area of high sensitivity
Page 6 - Two channel, single switch
3 Choosing a Suitable Location The EBDSPIR-DD is designed to be ceiling mounted and must satisfy the following criteria: Avoid positioning the un
Page 7 - Single channel switching
4 Installation The UNLCDHS has the ability to read back the settings stored in a device. To read back individual parameters Navigate to the param
Page 8 - SHIFT 1 SHIFT 2
5 Single channel dimming Channel 1 (switched output) of the EBDSPIR-DD can either be used to switch a separate channel of standard, non-dimming lumi
Page 9
6 L/OUTLNEBDSPIR-DD SENSORSW1/UPSW2DOWNPLEASE NOTE THAT THEDIMMING SIGNAL IS USED TOSWITCH THE DIMMINGLUMINAIRE ON/OFF ANDTHEREFORE THE 240V FEEDTO
Page 10 - Advanced programming
7 When power is applied to the unit, the load will turn on immediately. Set the timeout to 10 seconds, vacate the room or remain very still and wait
Page 11
8 Basic programming Parameter Name Default Value 0 1 2 3 UHS5 Handset Graphics Description Button Activation On / Raise On Raise
Page 12 - Part numbers
9 Advanced programming Parameter Name Default Value Range / Options Description UHS5 UNLCDHS Detector Parameters Walk Test LED Off On or O
Related products and manuals for Relay Cp-electronics VITM6-EBDSPIR-DD
Relay Cp-electronics VITP-IR User Manual
(12 pages)
(12 pages)
Relay Cp-electronics VITP-PD User Manual
(2 pages)
(2 pages)
© 2020, manymanuals.com. All rights reserved. | 0.612 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals